Miele Clothes Dryer T1520 User Manual

Operating Manual

for the T 1520

Vented Dryer

In order to protect yourself and

avoid damage to your machine,

it is absolutely necessary to read

the operating instructions prior

to installation and operation.

]

M.-Nr. 05 275 050

Guide to the machine

1 Supply cable with plug

2 Control panel

3 Drum door

4 Exhaust connection (right, left or rear)

5 Four height-adjustable legs

Guide to the machine

Pushbuttons

Indicator lamps

– Door

– PROGRAM SEQUENCE

The program sequence indicator

lamps show the current state of the

drying program.

This button is used to open the door

(does not stay pushed in).

– ON / OFF

When the machine is turned on, the

“On” indicator will light up if the door is

closed. If the door is open, the drum

light will be on.

– DRYING STAGE REACHED

These indicator lamps show which

drying stage the program has

reached. For program stages “Nor-

mal” and “Extra dry” the indicator

lamp remains at the “Normal” posi-

tion.

– Buzzer

Allows the buzzer to sound when the

drum rotates during the anti-crease

cycle.

PROGRAM SETTING-SELECTOR

– Load size - Full / Half

Set the required program by turning

the knob either clockwise or counter-

clockwise.

To dry a standard size load at peak

efficiency, press this button before

starting the drying cycle.

– COTTONS

– Start

Starts the selected program (does

– PERMANENT PRESS

not stay pushed in).

– TIMED DRYING

Items can be either dried for 20

minutes (incl. a cooling-down phase)

or cool air fluffed for 15 minutes.

IMPORTANT SAFETY INSTRUCTIONS

WARNING - To reduce the risk of fire,

electrical shock, or injury to persons

when using your appliance, follow

basic precautions, including the follow-

ing:

7. Clean the lint filter before and after

each load.

8. Do not dry articles that have been

previously cleaned in, washed in,

soaked in, or spotted with gasoline,

dry-cleaning solvents, other flamm-

able or explosive substances as they

give off vapors that could ignite or

explode.

1. Read these operating instructions be-

fore using your dryer for the first

time, as this is for your own safety

and for the protection of your ma-

chine.

9. Do not allow children to play on or in

the appliance. Close supervision of

children is necessary when the ap-

pliance is used near the children.

2. Remember to remove the door when

disposing of an old machine to pre-

vent children from accidently locking

themselves in the machine and en-

dangering their lives.

10.To avoid back-pressure or accumula-

tion of exhaust fumes, provide ade-

quate room ventilation, by means of

permanent vents or an open window.

3. Do not install or store this appliance

where it will be exposed to the

weather.

11.Always close the door after use to

prevent children from leaning on the

door and causing the dryer to tilt.

4. Do not install your dryer in rooms

where freezing temperatures may

occur. The reliability of the electronic

control system may be impaired.

12.Keep area around the exhaust open-

ing and adjacent surrounding areas

free from accumulation of lint, dust

and dirt.

5. This machine should only be used for

drying the following fabrics:

– Items which can be machine dried

as specified by the laundry care

label.

– Items which have been washed in

water.

6. The following fabrics pose a fire ha-

zard:

– Items which contain foam rubber,

rubber or rubberlike components.

– Items which have been treated with

inflammable cleaning agents, such

as gasoline or dry-cleaning solvents.

– Items containing hair lacquer, hair-

spray, nail polish remover or similar

substances.

IMPORTANT SAFETY INSTRUCTIONS

13.The interior of the machine and ex-

haust duct should be cleaned peri-

odically by qualified personnel.

19.Do not place items exposed to

oils in your dryer. Items contaimed

with oils may contribute to a

chemical reaction that could

cause a load to catch fire.

14.Do not reach into the dryer if the

drum is moving.

15.Do not tamper with controls.

SAVE THESE INSTRUCTIONS

16.Do not repair or place any part of the

appliance or attempt any servicing

unless specifically recommended in

the user maintenance instruction or

in published user repair instructions

that you understand and have the

skills to carry out.

For grounding and electrical

connection instructions, refer

to the electrical connection

section.

This dryer is only intended for

residential use!

Repairs to electrical appliances

should only carried out by qualified

personnel.

Incorrectly repaired machines may

pose a considerable risk to the user.

17.Formation of lint.

Lint is principally the result of friction

when items are worn and washed.

Machine-drying hardly causes any

lint to form and, as has been estab-

lished by reseach institutes, has no

effect on the lifetime of fabrics.

18.Warning - Do not use fabric sof-

tener/anti static dryer sheets.

Residues from these products block-

up (clog) the lint filter causing prema-

ture failure of the dryer.

Miele dryers are designed to dry

laundry without static cling. How-

ever, should fabric softener be re-

quired, use liquid fabric softener in

the wash cycle.

Clean lint filter mesh monthly by wash-

ing/scrubbing with hot soap and

water.

Your contribution to the environment

Disposal of the packing ma-

terial.

The transport and protective packing is

mostly manufactured from the following

recycled or re-useable materials:

Disposal of your old machine.

Old machines contain materials which

can be recycled. Please contact your

recycling center or scrap merchant

and render the machine inoperative as

per the “Important Safety Instructions”

before disposing of the appliance.

– corrugated paper/cardboard

– polystyrene - CFC-free

– polyethylene foil (transparent)

– untreated wood

– fiber board

Please check local environmental regu-

lations before disposing of packing ma-

terials and discarding the appliance.

OPERATING INSTRUCTIONS

WARNING - To reduce the risk

Unloading the machine

of fire, electric shock, or injury

to persons, read the IMPORT-

ANT SAFETY INSTRUCTIONS

before operating this appliance.

If the wash is not removed at the end

of the drying program, the machine

will automatically enter the anti-

crease cycle for 60 minutes. This en-

tails the drum being rotated at short

intervals in order to reduce the forma-

tion of creases.

Loading the machine

Load the laundry loosely into the

drum.

Once the laundry has been

removed, check that the drum is

empty. Any items left in the drum

could be damaged through over-

drying during the next program.

Duvet covers and pillowcases

should be fastened before drying in

order to prevent small items from roll-

ing inside of them.

Clean the lint filter after each drying

cycle to prevent excessive energy

consumption, longer program times

and the risk of fire.

The door should always be closed

after use.

Important: Check that laundry can-

not be trapped by the door as this

may cause damage to the fabric.

Notes on laundry care

Before drying, check the instructions

on the fabric care label.

Notes:

Knitted fabrics and flannel sheets tend

to shrink when washed for the first time

and also when dried. They should not

be overdried (Extra dry)!

The following fabrics should not be

dried in a tumble dryer:

– Woollens and wool blends

These fabrics tend to become matted

and shrink.

Starched laundry can also be dried in

the tumble dryer.

– Items filled with down

The fine fabric interior tends to shrink, Permanent press items should be

depending on the quality of the item

involved.

– Pure linen

briefly spun in the washing machine be-

fore drying. Items which are prone to

creasing should not be dried in the

These items should only be machine- “PERMANENT PRESS- Normal +” - Pro-

gram.

dried if specified as suitable by the

manufacturer on the textile care label.

The surface of the fabric may other-

wise tend to become “rough”.

Drip-dry shirts made of pure cotton

may tend to crease, depending on the

quality of their finish.

These items should be dried in a

“Hand iron”program.

Permanent press fabrics tend to crease

more as the size of the load increases.

This is particularly true of very delicate

fabrics. The load should be reduced to

1.5 kg or, if necessary, to 1 kg.

Miele dryers have been designed to

dry laundry free of static cling, without

the use of dryer softener sheets or simi-

lar products. The dryer continuously

monitors the moisture content of the

laundry, and automatically shuts off the

heat when the selected degree of dry-

ness is reached. Through the use of a

cool down period, (where the machine

operates without heat), cool, static free

laundry is the end result. Dryer softener

sheets perform the same function by

depositing a chemical residue on both

the clothes and the interior of the dryer.

Over time, this coating may lead to per-

formance reductions in the dryer.

Do not dry new dark-colored fabrics

together with light-colored items as

they may discolor.

If fabric softening is desired, it is more

convenient, economical and beneficial to

the clothing if a liquid softener is auto-

matically dispensed while the clothes are

in the washing machine. Please see the

washing machine operating instructions

for directions on how to automatically dis-

pense a liquid softener.

Program selection

Functional description

– Load size - Full / Half

To dry a standard size load of 2,3 kg

or more at peak efficiency, press this

button before starting the drying

cycle.

An electronic sensor system monitors

the moisture content of the laundry.

Once the required degree of dryness is

reached, cold air then enters the drum

to cool the laundry.

– Start

Starts the selected program.

The drying program is then terminated.

“PROGRAM SEQUENCE”

indicator

Function of the pushbuttons

The program sequence indicator lamps

show the current status of the drying

program.

“DRYING STAGE REACHED”

indicator

This indicator shows which drying

stage the program has reached.

“PROGRAM SETTING” selec-

tor

There is a range of settings for both

“Cottons” and “Permanent Press”.

In addition, items can be either dried

for 20 minutes (incl. a cooling-down

phase lasting 8 mins.) or fluffed in cool

air for 15 minutes.

– Door

This button is used to open the door.

– ON/OFF

When the machine is turned on, the

“On” indicator lamp illuminates when

the door is closed. When the door is

open, the drum is illuminated.

– Buzzer

When activated, the buzzer will sound

as the drum rotates during the anti-

crease cycle.

Program selection

To select a program

To change a program during

drying

A program can only be selected

when the machine is turned on.

Set the program selector to the

desired program.

The new program will start from the be-

ginning.

The tables on the following pages lists

the range of applications for the differ-

ent programs.

Correct procedure

1Press the “On/Off” button.

2Press the “Door” button and load the

drum.

Set the desired program by turning

the program selector either clock-

wise or counterclockwise.

3Close the door with a firm swing - do

not push it shut.

4If drying a standard load, press the

Press the “Start” button.

"Load size" button.

The program status will be stored for

30 minutes in the event of a power

failure.

5Select a program.

6Press the “Start” button.

The program is cancelled if

After the program has finished

– There is a power failure lasting more

than 30 minutes.

– The program has already reached

the “Cooling down” or “Anti-crease”

stage.

1Set the program selector to “Finish”.

2Remove the laundry.

3Clean the lint filter.

4Turn off the machine.

Programs

COTTONS

Type of laundry/fabric

Max. load

Special instructions

Multi-layer fabrics, mixed

load of cotton fabrics,

e.g.jeans, towels,

sweatsuits.

5 kg

The “Extra dry” program

should not be selected for

jersey wear items.

Extra dry

Homogeneous loads of

cotton fabrics e.g. flannel

items, underwear, socks.

5 kg

Should items still be damp,

select the “Extra dry”

program.

Normal

Knitted cotton fabrics

particularly suspectible to

shrinkage, e.g. jersey wear

or lightweight cotton

fabrics.

Should items still be damp,

select the “Normal“

program.

Normal- *

Cotton or linen fabrics, e.g.

linens, bedding, starched

items left damp for easier

ironing.

5 kg

Moisture can be increased

or decreased by using

“Hand iron rr” or “Hand

iron r” respectively.

Hand iron rr *

Cotton or linen fabrics,

including starched laundry,

for the rotary iron, (B865E).

The laundry can be rolled

up to prevent it from drying

out until it can be ironed.

Machine iron

* These are the programs that should be tested according to the EN 61121/A11 Standard.

Programs

PERMANENT

PRESS

Type of laundry/fabric

Max. load

Special instructions

Permanent press items

made of synthetic or

blended fabrics, e.g.

pullovers, dresses, pants,

etc., which are not dried

adequately in the “Normal”

program.

2.5 kg

With blended fabrics

consisting of wool and

synthetics, consult the

manufacturer’s

instructions, as the wool

component may cause the

fabric to become matted

and shrink.

Normal +

Permanent press shirts,

table cloths, bedding etc.

made of blended woven or

knitted fabrics, e.g.

2.5 kg

Normal *

cotton/synthetic.

Permanent press shirts,

table cloths, pillowcases

etc. cotton/synthetics,

Hand iron

which are still to pressed.

* This is the program that should be tested according to the EN 61121/A11 Standard.

TIMED DRYING

Type of laundry/fabric

Max. load

Special instructions

Individual items, e.g.

comforters, or very small

loads.

This setting will run the full

length of time regardless if

the item is dry beforehand.

warm

Items which are only to be

aired.

5 kg

cool

USER MAINTENANCE INSTRUCTIONS

Cleaning and care

Cleaning the dryer

Before cleaning the tumble dryer;

disconnect the machine from the

power supply.

Cleaning the lint filters

The lint is collected by the lint filter in

the door.

The dryer can be cleaned using

soapy water or a mild detergent (not

scouring powder) and dried with a

soft cloth.

Clean the filter after every program.

The drum may be cleaned using a

suitable stainless steel cleaner follow-

ing the manufacturer’s instructions.

The machine must never be hosed

down. Do not use any abrasive sub-

stances or scouring pads to clean

the machine.

Grip the filter by the recessed

handle and pull up to remove.

Any remaining lint in the hollow part

of the door can be removed through

the gap at the bottom.

The lint filter can be rinsed with water if

necessary.

Dry the lint filter before putting it

back in place.

Problem solving guide

Electrical appliances should only be repaired by qualified personnel. Incor-

rectly repaired machines may put the user at risk. There are, however, minor

problems which can be corrected without contacting the Service Department.

What to do if, . . . ? Cause . . .

Remedy . . .

Check whether the “On”

Repeat the switch-on procedure

in the correct sequence, as

outlined in the “Program

Selection” chapter.

. . . the tumble dryer fails to

start when turned on?

indicator lights up. If so, failure

to start may be due to an

incorrect program selection

procedure.

If the “On” indicator lamp does

not illuminate, check that:

–

The “ON/OFF” button is

depressed.

–

The door is properly closed.

The machine is plugged in

and the fuse or circuit breaker

has not tripped.

The load consists of dissimilar

items (size and fabrics).

Select a longer drying program.

. . . the laundry is not suffi-

ciently dry?

Small loads or individual items

may cause the program to

Small loads can be time-dried.

terminate the cycle prematurely.

The lint filter is clogged.

Clean the lint filter in the door.

. . . the drying times are too

long?

The laundry was not spun in the Make sure that the laundry is

washer for a sufficient time. thoroughly spun before drying.

–

Turn the program selector

to “finish”.

Turn the machine off and

then on again.

. . . the “anti-crease” indicator

lamp in the sequence indica-

tor display starts flashing?

–

Select a program.

Press the “Start” button.

If the indicator lamp starts

flashing again, this indicates a

fault in the machine.

Please contact the Miele

Service Dept.

Problem solving guide

What to do if, . . . ? Cause . . .

Remedy . . .

The machine has overheated.

The temperature limiter opened proceed as follows:

the drum door and caused the

machine to turn off

automatically.

Before restarting the program,

. . . the drum door opens dur-

ing the drying cycle?

–

Release the ON/OFF button.

Clean the affected part of the

machine.

Possible reasons for

overheating:

–

Turn on the machine again.

Reselect the terminated

program.

–

The lint filter in the door is

clogged.

–

Press the “Start” button.

–

The vent duct is blocked.

The vent aperture (e.g.

louvred window vent,

wall vent) is blocked.

If the drum door opens again,

the Miele Service Dept. should

be contacted.

See next page.

. . . the interior drum light fails

to function?

. . . you have to open the door

in the event of a power

failure?

Problem solving guide

The interior drum light fails to func-

tion: The bulb may be defective.

To open the door in the event of a

power failure

Replace it as follows:

Turn off the machine or disconnect

it from the power supply.

Open the door.

Pull forward on the un-hinged side of

the door.

Unscrew the plastic bulb cover lo-

cated inside the drum and above the

door (see illustration).

The light bulb must not exceed the

maximum wattage quoted on the

data plate.

Replace the bulb and the plastic

cover.

The cover must be correctly installed

and tightened, otherwise moisture may

seep in and cause the socket to cor-

rode.

This is a temperature-resistant bulb

and should only be ordered from your

Miele Service Dept.

After-sales service

In the event of problems which cannot

be solved, please contact:

– Your Miele Dealer

– The nearest Miele Service Depart-

ment (see back cover for the adress).

When contacting the Service Depart-

ment, please quote the Model and Se-

rial numbers of your appliance, both of

which can be found on the right side

after the door is opened.

Specimen:

INSTALLATION INSTRUCTIONS

Grounding and Electrical con-

nection

Electrical connection

This installation should be done by an

experienced and qualified person, in

most cases a licensed electrician, in ac-

cordance with local codes and regula-

tions.

Grounding instructions

This appliance must be grounded.

In the event of a malfunction, ground-

ing will reduce the risk of electric shock

by providing a path of least resistance

for the electric current. This appliance

is equipped with a cord having an

equipment grounding conductor and a

grounding plug. The plug must be

plugged into an appropriate outlet that

is properly installed and grounded in

accordance with all local codes and or-

dinances.

This dryer is supplied with a 1.5 m power

cord with a 3-pole, 4 wire grounding plug,

14-30P (regular Canadian dryer plug).

This plug has to be plugged into a 3-pole,

4 wire grounding receptacle, 14-30R

(regular Canadian dryer receptacle).

The receptacle has to be connected to

Line 1, Line 2, Neutral and Ground wires.

The voltage is 120/240 V AC or 120/208 V AC.

“EASY INSTALLATION KIT”

If you do not have a designated line,

4 wire, 120/240 V – 15 or 30 Amps, for

this appliance, but you have the 4 wire,

120/(208)240 V – 30 Amp Canadian

dryer wall receptacle (14-30 R) you can

use the Miele Double Receptacle Box.

This consists of two standard recep-

tacles 14-30 R, 4 fuses, box and plug

cord, which allows you to use that

single dryer wall receptacle to supply

power to a Miele washer and Miele

dryer. Both machines may operate at

the same time because each uses

maximum about 15 A current.

Warning

Improper connection of the equip-

ment-grounding conductor can re-

sult in a risk of electric shock.

Check with a qualified electrician or

serviceman if you are in doubt as to

whether the appliance is properly

grounded.

Do not modify the plug provided

with the appliance; if it will not fit the

outlet, have a proper outlet installed

by a qualified electrician.

For more information on the electrical

connection on the Miele Double Recep-

tacle Box please contact:

– your Miele dealer

– the nearest Miele Service Depart-

ment.

Installation

Where to install the machine

Take into consideration the space

required by the vent duct when cal-

culating the distance between the

machine and a wall or other ap-

pliances or cabinetry on either side.

Installation

It is possible to install this appliance

under a continuous countertop. The ma-

chine lid can be removed.

Flat ducting * may be required if there

is not enough space for a standard

duct.

The machine should be level to ensure

safe and proper operation. Minor dis-

crepancies do not, however, have an

adverse effect on operation.

The tumble dryer can also be placed

on the top of a Miele washing machine

for a stacked installation appropriate

stacking kit * to match your washing

machine is required.

* These items are all available from the

Miele Parts Dept.

The machine can be leveled by turn-

ing the legs clockwise or counter-

clockwise as necessary.

Turn the counternuts up and tighten

against the bottom.

Installation

Decor panel dimensions

Changing the decor panel

(Values in bracket demote tolerances

in mm)

Note: The door should be closed

when installing the decor panel.

Width:

Height:

Thickness:

587 mm (- 1)

602 mm (- 1.5)

1 mm (+ 0.5)

On the door lock side remove the 4

screws (3 on the side and 1 under-

neath) and the door strip.

Panels which are thicker than 1.5 mm

require a 4 mm adapter strip available

from Miele specialist dealers or the

Miele Spares Dept.

Loosen the remaining 7 screws on

the lower and side decor strips until

the decor panel can be bowed

slightly and taken out.

Note:

When using the adapter strip, the

height of the panel should not exceed

596.5 mm (- 1.5).

Reassemble in the reverse order and

tighten the screws.

Installation

Fitting a toekick panel

The appliance toekick below the door

can be concealed using a toekick

panel.

The height and depth of the appliance

toekick cannot be altered.

A cut-out must be made in the toekick

panel around the ventilation slots as

otherwise the airflow to the appliance

will be blocked and the machine will

not dry efficiently.

Installation - venting

The moist air from the dryer must be

Installation at the rear

vented to the outside.

The machine comes supplied with the

connector installed on the rear exhaust

port.

The appliance should not be vented

into a chimney, a wall, a ceiling, or

any concealed spaces of the building.

Installation at the left or right side of

the machine

Each side exhaust port has a framed

exhaust cap.

When installing, try to avoid:

– very long venting systems

– too many bends or angles

– tight corners

otherwise . . .

. . . the drying result will be affected,

. . . drying will take longer and use more

energy.

Materials suitable for venting:

– rigid metal pipe

– flexible metal pipe

Install the venting in such a way that

the expelled air cannot be drawn

into the machine.

Do not vent the dryer into a flue

used by gas or fuel boilers or

heaters.

A vent connector is included as stand-

ard. It should be pressed into the vent

outlet and will enable the connection of

exhaust pipe.

Before installation, disconnect the

tumble dryer from the electrical sup-

ply, (unplug from the wall socket, or

isolate at the main fuse box).

Only the cap should be removed,

and not the frame.

Exchange the rear exhaust connec-

tor for the side cap, and vice versa.

Install the exhaust pipes.

The exhaust connection can

be made:

– at the rear or

– at the left or right side of the machine

Installation - venting

The shorter the exhaust ductwork, the

more efficient the dryer will be. Ex-

pelled air is slowed down in the ducts

due to friction against the inner walls,

therefore the shorter and smoother the

inner walls are, the less friction will

occur.

An elbow or bend creates more friction

than a straight duct. An additional duct

length factor must therefore be added

for each elbow or bend (see Table I).

This factor expresses the resistance of

the bend in terms of a straight length of

duct.

The additional length factor is then

added to the measured duct length to

give the effective duct length.

A larger duct diameter also helps to re-

duce friction. The duct diameter should

therefore be increased with increasing

duct length.

Measure the actual duct length.

Establish the number of elbows or

bends necessary, noting the type of

bend, angle and radius involved

(see Table I).

Add the additional length factor as

specified in Table I to the actual duct

length to give the effective duct

length.

The necessary duct diameter should

then be found in Table II.

Note:

Drying times and energy consumption

remain unaltered for 100 mm duct up

to a total length of 10 m.

Longer duct may lead to slight in-

creases in drying times and energy

consumption but will not impair the

function of the machine as long as the

necessary duct diameter is used (see

Table II).

To calculate the effective duct length.

Tabel I

Type of bend

Angle

Radius in mm

Additional duct

length in m

Flexible metal piping

90°

45°

100-300

300-500

100-500

0.5

0.4

Plain piping

90°

100

0.4

2.5

0.8

0.6

3.8

Elbow

Concertina bend

Segmented bend

90°

200

Wall vent kit with louvres, or window vent kit

Wall vent kit with flap, or window vent kit

1.5

Exhaust connection, left/right side

Flat section adaptor

6/10

Installation - venting

Table II

Example:

Exhaust connection, left . . . . . . . 6.0 m

Length (L) . . . . . . . . . . . . . . . . . . 0.6 m

Lower radius (R = 400 mm) . . . . 0.4 m

Height (H) . . . . . . . . . . . . . . . . . . 1.5 m

Upper radius (R) . . . . . . . . . . . . . 0.5 m

Wall pipe with louvred vent . . . . . 3.8 m

Effective duct length . . . . . . . . . 12.8 m

Effective duct

length (m)

Internal diameter or

edge length (mm)

0-20

20-30

30-43

43-60

100

110

120

130

Flexible ducting has been used for the

following example.

Result:

A duct diameter of 100 mm is adequ-

ate since the effective length is less

than 20 m as specified in Table II.

Installation - venting

Moist air can be ducted outside by a wall

vent or window vent, both of which are

available from most hardware stores.

Window vent kit - example

Wall vent kit - example

1. Louvred window vent frame

4. Louvred window vent

5. Flap

8. Clips (4 pcs.)

9. Raised head screws (4 pcs.)

1. Louvred wall vent frame

2. Wall vent duct

3. Adapter

4. Louvred wall vent

5. Flap

Dryer-side view:

6. Screw

7. Wall anchor

Dryer-top view:

1. Window vent kit

2. Adapter for vent duct

The window vent kit is installed into in a plexi-

glass pane. If using an existing glass pane, cut a

hole with a diameter of 125 mm.

1. Wall pipe

2. Flexible foam-gasket

A flexible foam gasket must be used if the

tumble dryer is directly connected to the wall

vent.

Installation - venting

Fig. 1

Fig. 3

Ducting (side view) with flexible vent hose to an

exhaust flue.

Connection of piping to the tumble dryer.

1. Drain pipe

2. Adapter for vent duct between tumble dryer

and plastic drain pipe

1. Wall vent duct A. Wire spiral-wound hose

2. Adapter

B. Flexible ducting

3. Flue isulated against damp

Fig.4

Fig. 2

Height of vent outlet for washer dryer stack.

Ducting (side view) with plastic piping to a wall

vent kit.

1. Wall vent kit

2. Adapter

3. Drain pipe (outer dia. 110 mm)

Consumption data

load

Final spin speed

in washer*

Electrical

consumption

Drying time incl.

cooling down time

rpm

kwh

mins

Cottons

1200

1400

1550

3.32

3.16

3.06

Extra dry

1200

1400

1550

3.06

2.91

2.81

Normal

800

3.35

2.63

2.49

2.40

Normal-

1200

1400

1550

800

2.61

1.91

1.78

1.69

Hand iron rr

1200

1400

1550

1200

1400

1550

1.59

1.46

1.36

Machine iron

Permanent Press

2.5

1000

1.48

1.17

1.07

Normal +

Normal

Hand iron

The specified program running times and electrical consumption values were established under stand-

ard conditions (EN 61121/A11).

Different types of fabrics, load size and residual moisture after spinning may effect the specified

values.

*These values apply if the laundry is spun in a Miele washing machine before drying.

Technical data

Height. . . . . . . . . . . . . . . . . . . . . . . . . .

85 cm (adjustable +1/-0.5 cm)

Height with lid removed . . . . . . . . . . . .

Width . . . . . . . . . . . . . . . . . . . . . . . . . .

Depth (incl. distance from wall) . . . . . .

82 cm

59.5 cm

without lid 56 cm

with lid 60 cm

Weight . . . . . . . . . . . . . . . . . . . . . . . . .

Drum volume . . . . . . . . . . . . . . . . . . . .

Capacity. . . . . . . . . . . . . . . . . . . . . . . .

Rated load . . . . . . . . . . . . . . . . . . . . . .

Fuse rating . . . . . . . . . . . . . . . . . . . . . .

49 kg

99 l

5 kg dry laundry

2.7 kW

15 A minimum, or 30 A

4503

This paper is made from 100% chlorine-free bleached cellulose and therefore protects the environment.

Miller Electric Welder and DS 74D16 User Manual
Miller Electric Welding System RCT 224 Trailer User Manual
Multiquip Window HTN 27K TCSL User Manual
NEC Car Video System 2070WNX V User Manual
NordicTrack Home Gym VGR 850 User Manual
One for All Universal Remote URC 7010 User Manual
Optimus Portable CD Player CD 3860 User Manual
Panasonic Camcorder AJ D400P User Manual
Panasonic Cordless Telephone KX TG235CSK User Manual
ParaBody Home Gym 843101 User Manual