BULLETIN NO.
54-06-2411
SERVICE PARTS LIST
DATE
Feb. 2014
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
REVISED BULLETIN
54-06-2410
Cordless M12™ 3/8" Driver Drill
WIRING INSTRUCTION
STARTING
SERIAL NO.
CATALOG NO. 2410-20
C10B
SEE PAGE 3
EXAMPLE:
00
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
3
2
1
51
4
5
= Part number change
from previous service
parts list.
6
10
7
11
8
12
13
14
16
9
15
20
21
22
27
28
24
31
25
14
32
26
17
34
29
30
18
35
19
37
23
4
5
6
7
8
9 10 11 13 14 15 16 17 18 19 20
50231 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 38
37 38
39
40
41
42-70-0058
Improved
Design
53
Original
Design
42-70-0055
*
33
36
M12™ tools utilize two different Housing
Connection Clip designs depending on the
Handle Set . See page two for details.
38
39
45
FIG.
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PART NO.
---------------
---------------
---------------
44-10-0720
05-81-0535
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
23-30-0590
45-24-0875
---------------
45-24-0890
23-66-2736
31-15-1575
42-70-0055
---------------
06-82-6350
31-44-1240
14-30-1000
42-55-2410
---------------
---------------
12-20-1850
10-20-2697
DESCRIPTION OF PART
Carrier
NO. REQ.
(1)
(1)
(1)
(1)
(2)
(4)
(1)
(5)
(1)
(1)
(5)
(1)
(1)
(1)
(4)
(1)
(2)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(5)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
44
Ball Holder Plate
43
Rear Gearcase Housing
Speed Selector Wire Link
Shift Lever Screw
M3 x 12 Screw
3rd Stage Ring Gear
3rd Stage Planet Gear
Washer
52
3rd Stage Sun Gear
2nd Stage Planet Gear
2nd Stage Ring Gear
2nd Stage Sun Gear
1st Stage Ring Gear
1st Stage Planet Gear
Washer
42
42 47
49
52 53
M3 x 6 Screw
Motor Mount Plate
Motor Pinion
47
Motor Assembly
Hi/Low Speed Slide
Left Housing
48
*
Forward/Reverse Lever
Switch Assembly
46 See detail
LED Cover
46
47
48
49
50
51
52
53
Housing Connection Clip
Right Housing
FIG.
1
PART NO.
05-88-1680
42-66-0825
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
06-82-7336
---------------
---------------
---------------
---------------
---------------
---------------
---------------
---------------
DESCRIPTION OF PART
Chuck Screw
Chuck
M3 x 10 Screw
Spring plate Holder
Clutch Ring Cap
Clutch Ring Cup
Sleeve
NO. REQ.
(1)
M3 T-10 Housing Screw
Housing Kit
2
(1)
3
(4)
Gearcase Assembly
Carrying Case, Optional
Fuel Gauge
4
(1)
5
(1)
6
(1)
Fuel Gauge Label
Service Nameplate (Not Shown)
Warning Label (Not Shown)
7
(1)
8
Spring
(6)
9
Clutch Washer
Pin
(1)
10
11
12
13
14
15
16
17
18
19
20
(6)
FIG.
NOTES:
Ball
(6)
38,40,50 Service replacement gearcase assembly (50) comes with a
motor mount plate (38) that must be removed and discarded
when servicing. A motor mount plate already exists on the
motor assembly (40).
Gearcase Screw
Output Shaft
Ball Bearing
Stamping
(4)
(1)
(2)
(2)
Front Gearcase Housing
Retaining Ring
Outer Bracket
Locking Pin
(1)
(1)
MILWAUKEE ELECTRIC TOOL CORPORATION
(1)
13135 W. Lisbon Road, Brookfield, WI 53005
(6)
Drwg. 5
Cam Plate
(1)
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND
POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL
ORIENT MOTOR ASSEMBLY
WITH SLOT TO THE TOP
ROUTE WIRES 1 AND 2
THROUGH TRAPS IN
THIS AREA.
MOTOR
ASSEMBLY
1
2
FUEL GUAGE
LED ASSY.
WIRE TIE
FOR 2, 5 & 6
3
13
SLEEVED WIRES
(White, black, red,
green and gray)
BE CAREFUL AND
AVOID PINCHING
WIRES BETWEEN
HANDLE HALVES
WHEN ASSEMBLING.
5
6
8
7
10
11
12
PCB
4
1
WHITE
BLACK
RED
3
6
NOTE:
POSITION CONNECTOR PORTION
OF #13 WITH OPEN PINNED SIDE
FACING DOWN TOWARDS THE
PCB (WHITE WIRE SHOULD FACE
FRONT OF TOOL). BE SURE THAT
THE CONNECTOR IS FULLY SEATED.
5
13
GREEN
GRAY
2
PINNED SIDE OF CONNECTOR
TO FACE DOWN WHEN
INSTALLING TO
PC BOARD
4
SWITCH
8
7
9
CONNECTOR
BLOCK
ASSEMBLY
WIRING SPECIFICATIONS
Wire
No.
Wire
Origin or
Gauge
Length
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
-----
Terminals, Connectors and 1 or 2 End Wire Preparation
Component of the motor assembly.
Component of the motor assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly.
Component of the switch assembly / fuel gauge LED.
Color
1
2
Black
Red
23-30-0590
23-30-0590
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
23-66-2736
3
White
Black
Black
Red
4
5
6
7
White
Red
8
9
Red
10
11
12
13
Yellow
Blue
Black
Sleeve
|