Omnitron Systems Technology Network Card 10 100 Plus User Manual

negotiation and the Link Mode is “LS” Link Segment.  
available with the 10/100 Plus, including Link Segment  
(Normal Mode), Link Propagate (Link Loss Carry  
Forward), Remote Fault Detection and Symmetrical  
Fault Detection. The link mode assist in the  
identification and isolation of link failures.  
Accessories  
2. Connect the UTP port to a 10BASE-T or 100BASE-TX  
Ethernet device using a Category 5 cable (or better).  
Wall Mounting Hardware Kit  
USB Power Adapter Cable  
4381  
9130-2  
9113-PS  
miConverter10/100 Plus  
Media Converter  
User Manual  
3. Connect the fiber optic port to a 100BASE-FX Fast  
Ethernet device via the fiber cable of the appropriate  
mode and type. When connecting dual fiber models,  
the miConverter 10/100 Plus transmitter (Tx) must  
attach to the receiver side of its link partner; the  
receiver (Rx) must attach to the transmitter. When  
connecting single-fiber (SF) models, the Tx  
wavelength on one end has to match the Rx wavelength  
on the other. Based on this guideline, the SF media  
converter models must be used in pairs, such as the  
1130-2-x matched with the 1131-2-x.  
US Domestic AC Power Adapter  
Universal AC Power Adapter  
(requires AC power cord)  
9115-PS  
WARNING!  
Europe AC Power Adapter  
United Kingdom AC Power Adapter  
Australia AC Power Adapter  
Japanese AC Power Adapter  
European Connector Clip*  
UK Connector Clip*  
9116-PS-3  
9116-PS-4  
9116-PS-5  
9116-PS-8  
9116-3  
Before inserting the Power Adapter, verify  
that the power on the unit is appropriate  
for your AC line voltage source.  
miConverter 10/100 Plus Models  
Fiber Mode Type /  
Dual Fiber [DF] or Distance  
Single-Fiber [SF]  
Tx  
Rx  
Connector Types  
ST SC  
Lambda Lambda  
[nm]  
1310  
1310  
1310  
1550  
1310  
1310  
1550  
1550  
[nm]  
1310  
1310  
1310  
1550  
1550  
1550  
1310  
1310  
POWER ADAPTER NOTICE  
MM / DF  
SM / DF  
SM / DF  
SM / DF  
SM / SF  
SM / SF  
SM / SF  
SM / SF  
5km  
30km  
60km  
120km  
20km  
40km  
20km  
40km  
1120-0-x 1122-0-x  
1121-1-x 1123-1-x  
1121-2-x 1123-2-x  
9116-4  
This product should only be used with Omnitron supplied  
Power Supply model numbers 9113-PS, 9115-PS,  
9130-2, 9116-PS-3, 9116-PS-4, 9116-PS-5 or  
9116-PS-8.  
Australian Connector Clip*  
Japanese Connector Clip*  
9116-5  
4. Mount the miConverter 10/100 Plus using the  
included Velcro® strips or optional wall-mounting  
bracket kit (P/N 1091-0).  
9116-8  
-
-
-
-
-
1123-3-x  
1130-1-x  
1130-2-x  
1131-1-x  
1131-2-x  
*All spare Connector Clips are interchangeable with AC Power  
Adapters 9116-PS-3, 9116-PS-4, 9116-PS-5 and 9116-PS-8  
In order to guarantee performance when powering the  
miConverter 10/100 Plus with the USB Power  
Adapter cable (P/N 9130-2), the cable must be  
connected to a Full-Powered USB Type-A port (5V,  
500mA).  
5. Connect the appropriate power source.  
DESCRIPTION  
The miConverter10/100 Plusis a 10/100BASE-T copper  
to 100BASE-FX fiber media converter. The UTP copper  
port can automatically detect the speed, duplex mode  
and crossover mode of the connected device, or it can  
be manually configured via DIP-switches.  
DIP-SWITCH SETTINGS  
When choosing power options, replace (-x) in the model number  
with the suffix number that corresponds to the power supply of  
choice below. Example: 1103-3-6 stands for  
Link Mode  
UTP Mode  
1103-3-x with USB Power Adapter  
NOTE: Not all USB Type-A ports are Full-Powered  
USB ports. The Full-Powered USB Type-A ports  
are usually the USB ports found on computer  
cases or on self-powered (powered by an AC  
adapter) USB hubs.  
-1  
-2  
US Power Supply - 120Volt / 60Hz  
Universal Power Supply (requires AC power cord) -  
100-240Volt / 50-60Hz  
LS (default)  
LP  
AN Auto (default)  
MAN 10Mbps HD  
MAN 100Mbps HD  
MAN 100Mbps FD  
The 100BASE-FX fiber port operates in Full-Duplex  
mode and supports single-mode or multimode fiber  
with ST or SC fiber connectors. Single-mode models  
feature Bi-Directional fiber and support distances of  
up to 40km. The various fiber models options are  
described in the table on the first page.  
-3  
-4  
-5  
-6  
-8  
Euro Power Supply - 100-240Volt / 50-60Hz  
UK Power Supply - 100-240Volt / 50-60Hz  
Australia Power Supply - 100-240Volt / 50-60Hz  
USB Power Adapter Cable  
INSTALLATION PROCEDURE  
US/JPN Power Supply - 100-240Volt / 50-60Hz  
1. Configure the miConverter 10/100 Plus with the  
appropriate DIP-switch settings. The factory default  
configuration for the UTP copper port is “AN” Auto-  
For power supplies -3, -4, -5 and -8, country/region specific clips are  
used to provide the necessary power connection.  
Figure 1: DIP-switch Configurations  
Page 4  
Several Link Modes (fault-detection capabilities) are  
Page 2  
Page 3  
Page 1  
UTP Mode Selection  
Symmetrical Fault Detect (SFD)  
Link Propagate (LP)  
The UTP port is configured using the DIP-switches  
as shown in Figure 1. There are four modes of  
operation based on the position of the DIP-switches.  
The factory default configuration is “AN” Auto-  
negotiation. In the “AN” mode, the port will advertise  
100Mbps Full-Duplex, 100Mbps Half-Duplex, 10Mbps  
Full-Duplex and 10Mbps Half-Duplex.  
“SFD” generates a Link Loss signal on all ports on  
both media converters when a loss of link signal is  
detected by one of the ports. In Figure 2(E), the  
pattern of LEDs gives an indication of the failure  
point.  
“LP” generates (transmits) a link signal only when a  
link signal is detected. Utilizing this configuration, a  
loss of a receive link signal will continue to ‘propagate’  
through to the next port in the network. In Figure  
2(C), a loss of a receive link on the fiber optic port  
causes the UTP port to drop its link due to the  
propagated fiber optic link state. This setting allows  
the loss of a link to be detected by SNMP or other  
managed network devices to which the miConverter  
10/100 Plus is connected.  
LP  
RFD+LS  
RFD  
(D)  
(E)  
NOTE: Both media converters must be configured  
with the SFD Link Mode. The SFD function is only  
supported by Omnitron Systems equipment.  
Switch 1 Converter A  
SFD  
Converter B Switch 2  
SFD  
The UTP port can be configured for Manual negotiation  
by setting the appropriate DIP-switches. The port  
can be configured for 100Mbps Full-Duplex, 100Mbps  
Half-Duplex and 10Mbps Half-Duplex.  
Normal Operation  
RFD  
NOTE: Only the first loss of a receive link detected by  
the miConverter 10/100 Plus turns off the other port’s  
transmit link. An additional loss of a receive link on the  
other port has no affect on the miConverter 10/100  
Plus. The miConverter 10/100 Plus returns to normal  
operation when the first loss of a receive link is restored.  
Fiber  
Fiber  
UTP  
UTP  
Link Mode Selection  
(A)  
(B)  
(C)  
The miConverter 10/100 Plus can be configured for  
several different Link Modes. The DIP-switch  
illustration in Figure 1 indicates how to configure the  
different Link Modes.  
Switch 1 Converter A  
Converter B Switch 2  
UTP  
UTP  
Switch 1 Converter A  
LS  
Converter B Switch 2  
LS  
LED ON  
LED OFF  
LED Flashing  
LED ON or OFF  
Link Segment (LS)  
Remote Fault Detect + Link Segment (RFD + LS)  
“RFD+LS” generates a link signal only when a link  
signal is detected. However, instead of propagating  
the fault forward, the loss of link is looped back. In  
Figure 2(D), a loss of a received link state is looped  
back causing the port to stop transmitted the link  
state. Because the other unit is configured for Link  
Propagate, the UTP port will drop its link due to the  
propagated fiber optic link state.  
“LS” (factory default) generates and detects a link  
signal at each point in the network. Utilizing this  
configuration, a loss of a receive link signal will only  
affect the port detecting the loss of signal. All the  
other ports will continue to generate a link signal.  
Figure 2(A) indicates the normal operation of the  
system without faults. Figure 2(B) indicates a loss  
of a receive link on the fiber optic port, the UTP  
port continues to maintain its link.  
- LED status depends on the link  
type; AN - OFF, MAN - ON  
Switch 1 Converter A  
LP  
Converter B Switch 2  
LP  
Figure 2: Link Modes  
NOTE: It is not permitted to set both Converter A and  
B to RFD at the same time; a deadly embrace will  
occur.  
Switch 1 Converter A  
Converter B Switch 2  
Page 5  
Page 6  
Page 7  
Page 8  
 

Milwaukee Laser Level 2280 20 User Manual
Minicom Advanced Systems Computer Accessories 5UM30167 User Manual
Munchkin Indoor Furnishings MK0089 User Manual
Murphy Automobile Parts CNG 92200H User Manual
NEC Computer Monitor EA191M BK User Manual
NEC Flat Panel Television S401AVT User Manual
Norcent Technologies Digital Camera DCS 760 User Manual
NordicTrack Treadmill NTTL15510 User Manual
OPPO Digital Blu ray Player BDP 105 User Manual
Parrot Portable Speaker PF520130AA User Manual